PCI-6601
Hello, I'm trying to figure out if PCI-6601 counter/timer board is compatible with Windows 11 and the current LabVIEW 2025. That board has been installed and running on a Windows 7 computer so I wasn't...
View ArticlecRIO DAQmx synchronize internal signals
Hello guys,i want to generate a clock and trigger signal. the clock signal should start when the trigger starts. i cant figure out how to synchronize them. i attach my code..is it possibe to generate...
View ArticlePXIE-1095 Jitter at 100MHz
Hi Team,Please help to share the PXIE_CLK100 jitter value at 100MHz.Here is the datasheet values for other frequencies.The PXIe-1095 chassis features a maximum RMS phase-jitter of 5 ps (10 Hz–1 MHz...
View ArticleClik here to view.
Start Trigger for Analog and ArmTrigger for Counter task necessary?
Hey guys, I am currently trying to aquire data from an analog input task (pressure sensors conncected to a NI 9205) and a counter input task (measuring flange for angle measurements on a NI 9411) in...
View ArticleClik here to view.
Slew Rate Test Inquiry
I'm looking into the possibility of using a direct measurement of our test part which has a 2000V/us slew rate. I was planning to use Pxie 6571 to measure directly the device. I've seen the vector...
View ArticleCounter source used within DAQ Assistant CO pulse time
Hello, I learning to use Counter Continuous Pulse Output on USB-6363 OEM. I used DAQmx Create Virtual Channel (VI) CO pulse time.Though OK, I need to know what is the source (or time base) the...
View ArticleCounter source
Hello friends,I need some help. I am trying to determine the time between each pulse emitted by an output of the USB-6351 card on my test bench.To be more specific, this test bench emits an output...
View ArticleGenerating two digital waveform signals triggered by an X Series input...
Hello,I need your help. I am unable to generate two signals from a table on port 0 simultaneously. The DAQmx “write” function indicates that it is already busy. Do you have any idea what the program...
View ArticleBNC-2110 Voltage Drop with Multiple Connections
Hello NI Community, I'm facing a weird issue with our setup. The issue with our equipment when sending an analog signal into port AI3, the signal voltage drops when connected via a T-junction. The...
View ArticleUSB-6421 pulse width sensor class not appearing in flex logger
Recently ordered a USB-6421 along with a FlexLogger license to the newest version. The main purpose was because both the FlexLogger user manual and the USB-6421 user manual mention its ability to...
View ArticlecDAQ 9174 Counter Frequency Measurement
Hello, I'm currently struggling to set up my cDAQ 9174 with a NI 9402 digital module for a sample clock buffered frequency measurement. I can get this to work fine with my NI 9215 installed and...
View ArticleTriggering two functions: AI read and CITime, when reading from the same...
Hello, I want to read and determine the delays between each pulse of a waveform from an external source.To do this, in my VI, I measure the time/delay between each pulse and, at the same time, the...
View ArticleClik here to view.
Hardware Timed dual counter output with changing delay on second pulse
I am using a USB-6351 to control a piece of external scientific equipment. What I need from this device is the ability to generate two pulses. The first will be a consistent pulse triggered by an...
View Articlemeasuring encoders using PXI-6602 in LabVIEW Continuous Measurement Sample...
i'm trying to read position data from 4 linear encoders connected to a PXI-6602. i'm also trying to use the LabVIEW "Continuous Measurement" sample project. i have been trying to use a dummy analog...
View ArticleHow can I use a Buzzer Module for timing or alert functions?
I’m experimenting with a Buzzer Module and wondering how it can be integrated with a microcontroller’s counter or timer to generate timed alerts, notifications, or simple tone patterns, like in...
View ArticleClik here to view.
A trigger from a trigger (PCI6351)?
Hello everyone,I currently have a VI that generates two custom signals on two different digital lines from an external trigger. This external signal is shown in red on the diagram. It is fast, with a...
View ArticleDAQmx Timing Property Node: SampClk.Timebase.Src / Rate not visible in...
Problem DescriptionI am trying to synchronize two NI-DAQmx tasks that run on different C Series modules with different sample rates (Delta-Sigma module + slow sampled module), following NI’s...
View ArticleA method to move in 0.1-second increments and output at the specified time,...
Hello,I am using LabVIEW 2025 with the cRIO-9042. I am a beginner with LabVIEW. I would be happy if you could teach me. I have two problems. The first is about AO output. I want to set it up so that it...
View ArticleClik here to view.
DAQmxWriteCtrFreq starts out taking 3 ms to execute and then ends up taking...
I have a program that updates CTR/TMR channels for variable PWM signals at 1 Hz. As the title of the thread states, the function call for the update takes longer over time. It isn't a continuously...
View ArticleCan I warranty claim this? NI 9361
UrgentI purchased three NI 9361 cards last year. For one of the cards. I have everything unwired except a ground wired to COM to ground. I have set all 8 channels to single ended with 5V pullup. Here...
View Article